Posted March 21st, 2010
by admin
brooster asked: I went to their site and was unable to find out. I need to remove my blade and I am having difficulty because the nut is very tight. I am not sure wether it is left or right hand thread although the blade turns clockwise I would tend to think it should be left but I have been told that this is not always the case.
Tags: Blade, Hand Thread, Tight
Posted in Garden & Landscape | 4 Comments »
Posted February 28th, 2010
by admin
jules asked: I purchased a Honda rotary mower HRR216VXA last summer. When mowing, the blade disengages on its own. Wait lists at repair shops for this mower are long, please let me know any tricks to keep my lawn up with the joneses til I can have it fixed properly
Tags: Blade, Honda, Joneses
Posted in Maintenance & Repairs | 2 Comments »
Posted October 22nd, 2009
by admin
ann t asked: The blade is loose on the mower. I can’t tighten or loosen it.
Tags: Blade, Bolt
Posted in Maintenance & Repairs | 5 Comments »
Posted October 10th, 2009
by admin
David Huynh asked: and where can i get sae 30 motor oil
Tags: Blade, Lawnmower, Motor Oil
Posted in Maintenance & Repairs | 14 Comments »
Posted October 7th, 2009
by admin
Jill S asked: I can pull the starter will no problem and the blade just spins making this noise. There is no resistance when I pull the cord. I mowed the front yard, thought I was hearing a weird noise from the mower. Then went to mow the back and it quit after a couple of minutes. Now this is where its at. Any advice?
Tags: Blade, Resistance, Weird Noise
Posted in Maintenance & Repairs | 4 Comments »
Posted September 21st, 2009
by admin
Kev asked: I have a Briggs and Stratton lawnmower. The pull cord is jammed. When I pull it to start the mower, it comes out maybe 6 inches at the most then it won’t move. Subsequent attempts get hardly any movement at all. I’ve turned it on it’s side and the blade seems to turn okay. It did this a little towards the end of last summer but we haven’t really had any problems this summer so far. Any suggestions?
Tags: Blade, Briggs And Stratton, Lawnmower
Posted in Maintenance & Repairs | 3 Comments »
Posted August 24th, 2009
by admin
samantha s asked:
it only will run when the clutch is pressed in, you can change gears but when I take my foot off the clutch (which is also the brake) it dies. What could be the problem? Is there an easy fix for it?
I assume the blade is disengaged, but when you touch the handle to check it will shut off.
Tags: Blade, Clutch, Riding Lawnmower
Posted in Maintenance & Repairs | 4 Comments »
Posted August 10th, 2009
by admin
belle26101 asked:
It’s a Murray 3.5HP….20″ blade bought in 2007. The attachments holding the top down are flat…not screws which I’d be able to simply screw off! I asked this yesterday but am waiting to see if some1 can explain how to remove the top part.
Tags: Attachments, Blade, Doi
Posted in Garden & Landscape | 3 Comments »
Posted August 9th, 2009
by admin
crazy nurse asked:
I have moderate troube getting the outer blades off, but the center blade is impossible. Now the bolts are pretty well stripped and I have
invested 2 hours in trying to get if off, unsuccessfully. Any tips, now that the bolts are stripped.
Tags: Blade, Bolts, Lawnmower Blades
Posted in Maintenance & Repairs | 2 Comments »
Posted August 2nd, 2009
by admin
Tom F asked:
I have a Craftsman TS1000 riding lawn mower and my son ran over a large rock that damaged one of the two blades. After replacing the damaged blade, the lawn mower cuts unevenly. I put the lawn mower on a level surface and can see that the mower deck is uneven, but I don’t know how to adjust it. Can you help me?
Tags: Blade, Lawn Grass, Riding Mower
Posted in Maintenance & Repairs | 4 Comments »
